Privacy statement: Your privacy is very important to Us. Our company promises not to disclose your personal information to any external company with out your explicit permission.
Model No.: QNE400A
Brand: QUANNING
Current Type: Dc
Rated Insulation Voltage: 1200
MAX Voltage Switching: 1200VDC
Rated Operating Current: 400
Transportation: Ocean
Place of Origin: NANJING ,CHINA
Certificate: CE
Port: SHANGHAI
Payment Type: L/C
Incoterm: FOB
NanJing QuanNing Electric Co., Ltd.
QNE400A High Voltage Dc Contactor is used for auxiliary electrical switching control of electric vehicle, precharge control, electric vehicle, fast charging pile, battery switching and high voltage DC voltage switching control of electric motorcycle, circuit protection and safety control, etc.
●400A+ charging capacity, can rupture 2000A current at 320VDC; Small size, light weight. Auxiliary contact 30VDC/0.5A;
●The switch part and the driving part are inflated and sealed to cut off the high-capacity load.
●Fully sealed structure, high safety; Non-oxidation coils and contacts can be used in explosive or harmful environments, even for a long time;
●Product standard:IEC60947-4, GB14048.4
●Certification: CE
产品型号 (见型号说明) | QNE400A-G1-24-10 | |
主触点 contact | 额定绝缘电压 Rated Insulation Voltage Ui(V) | 1200 |
额定工作电压 rating voltage Ue(V DC) | ≤900 | |
约定发热电流 Conventional thermal current Ith(A) | 400 | |
额定工作电流 Rated operating current Ie(DC-1 A) | 400 | |
接触电阻resistance | ≤2mΩ (12VDC/10A) | |
最大切换电压 MAX Voltage switching | 1200VDC | |
最大切换电流 MAX Current switching | 2000A/320V | |
过载切断Overload cut-off | 320VDC 下 2000A,1 次 | |
峰值电流冲击Peak surge current | 4000A/500 次 4000A/500 times | |
触点形式contact form | 一组桥式常开Bridge 1NO | |
辅助触点 Auxiliary contact | 辅助触点电流最大值 Auxiliary contact MAX Current | 30VDC 2A,125VAC 3A,250VAC 0.5A |
辅助触点电流最小值 Auxiliary contact MIX Current | 8V 100mA | |
触点形式 contact form | 一组常开 1NO | |
|
|
绝缘电阻Insulation resistance | ≥100MΩ/500VDC | |
介质耐压Initial Dielectric Strength | 线圈与触点间Between Contacts and Coil | 2500VAC/min |
断开触点间Between The Open Contacts | ||
电气寿命 (阻性负载) Electrical endurance(Resistive load) | 1×104 次 (400V,400A) | |
机械寿命Mechanical endurance | 20×104 | |
动作时间active time | ≤20ms (包括触点弹跳时间) | |
释放时间Release Time | ≤12ms | |
冲击Impulse | 11ms,1/2 正弦波sine,峰值peak value,196 m/s2 | |
振动Vibration | 正弦波sine,10~2000Hz,峰值peak value,196 m/s2 | |
使用环境温度Ambient Temperature | -40~85℃ | |
使用环境湿度Ambient Humidity | 5%~85%RH | |
端子形式Wiring Terminal form | 螺纹连接型Thread connection type | |
封装形式Encapsulation form | 充气密封型Inflatable seal type | |
重量Weight | ~ 500g |
●线圈工作电压 (适用于整个温度范围) :
标准电压Standard voltage | DC12V | DC24V | DC48V |
工作电压working voltage | 9.6~13.2VDC | 19.2~26.4VDC | 38.4~52.8VDC |
最大电压MAX voltage | 15VDC | 30VDC | 60VDC |
最小吸合电压MIN pull voltage | 9.6VDC | 19.2VDC | 38.4VDC |
7、应用注意事项:
●不要在接触器通电状态下,触摸负载接线端子,谨防触电危险;
Do not touch the Relay terminal when it is energized or in danger of electric shock
●当对控制回路及非金属材料做耐压测试时,应断开负载电压;
Disconnect the load voltage when the voltage withstand test is conducted on the control circuit and non-metallic materials
●避免将产品安装在强磁场的地方 (变压器或磁铁) ,或靠近热辐射的物体;
Avoid installing the product in places with strong magnetic fields (transformers or magnets) or near objects with heat radiation
●不要将杂物和油污沾到主引出端子,且外引线端子与主引出端子可靠接触,否则会造成端 子发热很厉害,导致连接电缆皮熔化;
Do not stick sundries and oil stains on the main outgoing terminal, and the external lead terminal shall be in reliable contact with the main outgoing terminal, otherwise the terminal will be heated seriously and the connecting cable will melt
●在进行动作电压测试时,不要使电压缓慢上升,请通过阶段跃进式供电方式对线圈驱动;
Please drive the coil through step power supply instead of making the voltage rise slowly during the action voltage test
●接触器各部位螺钉拧紧力矩控制在规定的范围。负载安装部位的螺母拧紧力矩为 7N.m;接 触器安装部位螺柱扭力 8-9N.m;
Install within the specified range. The tightening torque of the screws at the load installation position is 7N.m · m; The tightening torque of the screws at the installation position of the contactor is 8-9N.m
●在接触器意外跌落并受到冲击的情况下,原则上请不要继续使用;
Do not use the relay in case of accidental drop and impact.
●接触器寿命终点,即绝缘仪直流 500V 时引出负载端之间绝缘强度低至 50 兆欧。
The end point of contactor life, that is, when the DC of the insulator is 500V, the insulation strength between the outgoing load ends decline to 50mΩ
●Notes:continuous output with current of 400A and lead of 300mm ² X2 wire. ( the temperature of control wire at 400A current is 85℃) Contact us if you want more details.
Product Categories : DC Contactor > High Voltage DC Contactor
Privacy statement: Your privacy is very important to Us. Our company promises not to disclose your personal information to any external company with out your explicit permission.
Fill in more information so that we can get in touch with you faster
Privacy statement: Your privacy is very important to Us. Our company promises not to disclose your personal information to any external company with out your explicit permission.